Loading...

Distilling Your Rum


Distilling Your Rum

No ratings yet
Print Rate

Equipment

  • Pot Still
  • Still Burner
  • Cleaning Products
  • Easy Siphon
  • Hydrometer

Ingredients

  • Rum Wash

Instructions

Fermented and Strained Rum Wash

  • Great job! So far you’ve come along way and done all of the work necessary to actually produce your fermented rum wash. That rum wash currently contains some undesirable contents that you’ll need to separate out and dispose of. This is where the distillation step of making your own rum comes in. This process of distilling the fermented rum wash will make for a purer and more concentrated spirit. This step separates out all of the undesirable types alcohols such as acetaldehyde, acetone and methanol (which can cause blindness if consumed).

Prepping and Cleaning Your Pot Still

  • Don’t skip this step! Unfortunately many people do and it causes a subpar product in the end. If you aim to maximize the quality of your distilled spirit, then it’s all about attention to detail. You’ll want to start on prep-work by cleaning your still. If this is your first run ever, below is a great walkthrough of how to setup your pot or reflux still.
  • Even if you’ve cleaned the still after your last run and let it sit for a while, you will want to clean it again. If you’re just now learning how to make rum, or any other spirit for that matter, now is the time to really emphasize this so you can build in good habits to your distilling routine.
  • Next, you’ll add your rum wash into the still. We recommend using a siphon for this process. This is the best way to reduce the amount of sediment from your fermented rum wash getting into the still. Particles and sediments can cause the distillation to burn and ruin your product so be diligent in this step.

Running Your Pot Still

  • It’s now time to fire up that pot still! Ensure that your still is properly set for this step. Secure all clamps and domes and make sure condensers are properly attached, as well as any hoses. Next, you’ll turn on the heat source and start raising the temperature of your rum wash. You’ll want to run the rum wash through two separate distillations. During the first, you’ll collect the entire distillate without separating the heads, hearts and tails. That will be done during the second round of distillation.
  • If using a condenser, turn on the water when the boiler reaches 130 °F.
  • At about 168 °F the still will start producing. Increase the temperature to keep producing distillate.
  • Stop collecting distillate after it measures less than 20% ABV which you can measure using the hydrometer. Be sure to hold on to the remaining contents of the still as you’ll be adding it back in with your second distillation. This will add to the final flavor of the product. Dilute the first round distillate by 20% with water. Stir the mix thoroughly and add back into the still. Begin your second round of distillation.

Collecting Your Rum Distillate

  • Collecting your rum distillate is the most satisfying part of this entire process. This step is a mixture of art and science, as it takes an experienced distiller to get this process just right. That being said, don’t let this deter you if you’re a newcomer to distilling. Everything comes with practice and after you run a few batches with your still you’ll definitely be able to dial things in by taking notes and making the necessary changes.

Foreshots

  • The first 5% of your run will consist of the foreshots. Foreshots contain methanol which is an extremely volatile and toxic alcohol. As a standard practice a good rule of thumb is to throw out the first 250 ml per 5 gallons as this part of your run will consist of these foreshots.
  • DO NOT CONSUME THIS PART OF YOUR RUN!
  • Be sure to isolate the foreshots thoroughly and throw them out. Consuming methanol can cause an array of issues including blindness.

Heads

  • The next 30% percent of your rum run is known as the heads. Similar to the foreshots, the heads of your run are filled with volatile alcohols. One of the staples of the heads is a particularly volatile alcohol known as acetone.
  • Acetone has a distinct, solvent-like smell, making its identification pretty easy to recognize. Drinking your heads won’t make you blind but they will leave you with the worst hangover of your life.
  • Like your foreshots, you’ll want to isolate these and throw them out.
  • *Note a great way of isolating both the foreshots and heads in your run is to bring your still to around 168 °F and keep it there for around 10 minutes. The alcohol produced during this duration will consist of only foreshots and heads. Once the condenser stops producing at 168 °F, you’ll know that you’ve collected all of the foreshots and heads of the run.

Hearts

  • If you’re following along with this guide, you have now officially gone from Googling “How to Make Rum” to actually making rum. The next 30% of your run will be the sweet spot of your rum run, the hearts. You’ll want to raise the temperature of your still to 175 °F to 180 °F range to start collecting this portion of your distillate.
  • You’ll notice the solvent smell of acetone taper off and a sweet-smelling ethanol come forward in your run. This is where a skillful distiller really shines. Maximizing high-quality hearts is a game of senses. You can recognize the hearts by their sweet and neutral flavor. *only taste a bit of the distillate on your finger. It’s not time for shot glasses yet my friend.
  • By accurately identifying where the acetone stops and the ethanol begins, a distiller maximizes their number of high quality jars of product. The main giveaways are the solvent smell of acetone and the sweet/smooth taste of ethanol.

Tails

  • The last 35% of your rum run will be the tails. You can recognize the tails by sight, smell and taste. You’ll see an oily film start to collect on the top of the distillate and be able to smell/taste a burnt type of flavor. The tails contain protein and carbohydrates from the wash that you don’t want in your final product.
  • Some tails have esters and other bi-products that can refine the character of your spirit and can actually add nice flavor to it. Be precise with your cuts and use your smell and taste to see what you like and don’t like in them.
  • Hold on to your tails and you can actually run them as their own wash in the future to pull out a bit more product.

Aging Your Rum

  • The results of aging rum can vary widely, depending on a few factors to consider. The type of barrel, whether charred or newer will greatly effect the flavors of the rum. A charred barrel will result in a darker and richer flavor, while a new barrel will deliver a lighter flavor. The amount of time that the rum is aged will also be a large factor in the final flavoring of the spirit. The longer you age your rum, the more time it has to soak up the flavors of the particular barrel you’re using. The area in which you are producing your rum also greatly affects the aging process. If you are in a more tropical climate, your rum will mature at a much higher rate. This is due to the amount of product lost due to evaporation. Always be sure to dilute your distillate to 50% before beginning the aging process.

White Rum

  • If your goal is to create a lighter white rum, than no aging is required. Simply dilute the drink with water to reach 45% and blend your mix thoroughly. Then bottle the spirit, and then leave for 3-4 days to let the tastes and flavors stabilize. You can also age your rum in a stainless steel barrel, which will let your rum age without darkening the color of the spirit.

Dark Rum

  • Many countries require that rum be aged after distillation for at least one year. This isn’t required by any means but it will definitely result in a darker and richer flavored rum. A good rule of thumb is to age your rum 6 to 18 months in a charred oak barrel or with oak chips to give your rum a distinct aged flavor. However long you decide to age your rum, you should blend your mix to ensure a consistent flavor. This is always the last step for any aged spirit prior to bottling.

Spiced Rum

  • After aging your rum, you can add much more flavoring by adding spices such as such as vanilla, peppercorns, cinnamon, allspice berries, cloves and nutmeg. This is where you can really experiment with the flavors and see what you like best. Be sure to add these spices in a separate container than the aging barrel used if you’d like to be able to experiment with different flavors for your next batch.

Conclusion

  • Congratulations! You have just made your own batch of delicious homemade rum. We hope this guide was helpful for you and you churned out a top-shelf spirit. Now comes the cleanup step. Be sure to wash everything thoroughly to ensure high-quality product in the future. Disassemble your still and store it in a cool, dry place.
  • Thank you for visiting Mile Hi Distilling, your one stop shop for all of your distilling needs. Don’t forget to check out our shop for any supplies or equipment you may need for any future distillations. We hope you enjoyed learning how to make rum with a raw cane sugar and molasses wash.

Leave a Reply